Boundary Devices launched this month an embedded platform developed in partnership with MediaTek. The device features an octa-core Arm Cortex CPU, an audio DSP, an Arm Mali-G57 GPU for 4k video codecs and 3.7 TOPS NPU for deep learning, computer vision, etc. The datasheet for the Tungsten700 indicates that this board is built around the […] ⌘ Read more
Boundary Devices launched this month an embedded platform developed in partnership with MediaTek. The device features an octa-core Arm Cortex CPU, an audio DSP, an Arm Mali-G57 GPU for 4k video codecs and 3.7 TOPS NPU for deep learning, computer vision, etc. The datasheet for the Tungsten700 indicates that this board is built around the […] ⌘ Read more
This week Lime Microsystems launched the LimeSDR XTRX which is a compact and powerful software-defined radio (SDR) board in a mini PCIe form factor. At its core, the board features an AMD Artix 7 FPGA and the Lime Microsystems LMS7002M RF transceiver to serve as a platform for developing logic-intensive digital and RF designs. According […] ⌘ Read more
The NanoPC-T6 is a single board computer based on the octa-core Rockchip RK3588 System-on-Chip. This SBC is equipped with interfaces including 2x HDMI output ports, 2x 2.5GbE for high-speed networking, 2x CSI connectors for camera integration and many other ports. As mentioned above, the NanoPi accommodates the Rockchip RK3588 processor with the following architecture: […] ⌘ Read more
SolidRun launched today a new SD-WAN appliance built around the Marvell OCTEON CN9131 System-on-Chip designed for intelligent networking applications. Some of the key features of the SOLIDWAN CN9131 are its multiple ethernet ports and wide expansion ports. The Marvell CN9130 family is described as a versatile System-on-Chip solution based on Armv8 CPU technology, suitable for […] ⌘ Read more
Today, Unitree unveiled their latest quadruped robot, the Unitree Go2. This robot comes packed with advanced features, including a 4D LIDAR sensor, a depth camera, and Wi-Fi6 connectivity. Additionally, the Unitree Go2 features an increased payload capacity in comparison to its predecessor. The product page shows that there are three Unitree Go2 variants available: Air, […] ⌘ Read more
Arduino announced yesterday a new development board from the Nano family. The Nano ESP32 integrates a u-blox NORA-W106 (Espressif ESP32-S3) module with support for Wi-Fi 4 and Bluetooth Low Energy 5. At its core, the Arduino Nano ESP32 houses the u-blox NORA-W106 (ESP32-S3) System-on-Chip, featuring a dual-core 32-bit Xtensa LX7 microprocessor (up to 240MHz), 512kB […] ⌘ Read more
The Alp Electronix RP2040-ESP32C3 Dev Board is a versatile and compact development board designed to meet the needs of both hobbyists and developers. The board is equipped with a MicroSD card slot, a 1.9″ LCD connector and various other features. The Alp Electronix Wiki pages mentions that “the main controller of this board is RP2040. […] ⌘ Read more
Kickstarter launched this week a Rotary Encoder equipped with an RGB LED array and a 1.28”round touch LCD. This device is compatible with open-source modules such as the Raspberry Pi Pico and the ESP32-S3 System-on-Chip from Espressif Systems. The first variant is powered by the Raspberry Pi Pico W platform which is based on the […] ⌘ Read more
M5stack introduced last week the UNIT-V M12 which is an AI camera unit that combines advanced specifications and a compact design. Equipped with an M12 lens and a Kendryte K210 System-on-Chip with machine vision capabilities. This new camera module appears to be an updated version of the UnitV k210 Edge Computing AI (EoL) released a […] ⌘ Read more
SeeedStudio recently featured a Single Board Computer based on a 32-bit STM32 MPU clocked at 1.0GHz. The ODYSSEY-STM32MP135D supports multiple operating systems and provides versatile connectivity options including two ethernet ports and one LCD connector. As its name implies, this new SBC accommodates the following STM32 microprocessor: STM32MP135D — 32-bit Arm Cortex-A7 RISC core (up […] ⌘ Read more
This week, Ambiq launched two powerful and energy-efficient System-on-Chips designed for a wide range of consumer wearable applications including healthcare products. Both variants are equipped with a 2D/2.5D graphics accelerator and one of them support Bluetooth Low Energy connectivity. According to Ambiq, the Apollo4 Blue Lite SoC is built on their own proprietary Subthreshold Power-Optimized […] ⌘ Read more
BeagleBoard.org launched today the open-source BeagleV-Ahead. This new open-source RISC-V Single Board Computer is powered by the Alibaba T-head System-on-Chip which combines a quad-core RISC-V CPU, 4 TOPS NPU and 50 GFLOPS Imagination BXM-4 GPU. As previously mentioned, the BeagleV-Ahead accommodates the Alibaba-T-Head TH1520 SoC with the following features: TH1520 — quad-core 64-bit RISC-V 64GCV […] ⌘ Read more
AnalogLamb is set to release three affordable RISC-V breakout boards. These boards are based on the CHV32 Series microcontrollers offering support for standard interfaces such as I2C, SPI, UART, CAN, DMA, among others. The first breadboard is called the Polos CH32V003 which integrates the CH32V003F4U6 in a QFN20 package. CH32V003F4U6 — QingKe 32-bit RISC-V2A processor, […] ⌘ Read more
The MicroGEA STM32MP13 is a small embedded product based on one of the latest STM32 processors designed for wearables and low-powered consumer applications. Additionally, the device is industrial qualified and supports Linux operating systems. According to the product brief, the MicroGEA STM32MP13 integrates the following microcontroller: STM32MP135 — 32-bit Arm Cortex-A7 (Up to 1.0GHz); L1 […] ⌘ Read more
The CBx3 and CBx3-7 are two compact devices based on a Celeron processor from the 7000 Series and an i7-1355U 13th Gen processor respectively. These compact devices offer an array of features including Gigabit ethernet, Wi-Fi6E/BT5.3, dual HDMI ports, etc. As mentioned above, the CBx3 Chromebox is equipped with a Celeron P7305 processor while the […] ⌘ Read more
Sipeed recently launched new variants of the Lichee Pi 4A with more RAM and eMMC storage. This RISC-V based SBC comes with 2x Gigabit Ethernet ports, 4K display output and support for wireless networking. At the heart of the Lichee Pi 4A is the TH1520 System-on-Chip, built on a 12nm process and featuring the RISC-V […] ⌘ Read more
The Youyeetoo YY3568 is a development board based on the Rockchip RK3568 quad-core 64-bit processor. This embedded product offers a range of versatile features, including a SATA 3.0 interface, a CSI connector, and support for multiple displays. At the heart of the youyeetoo YY3568 System-on-Module is the Rockchip RK3568 System-on-Chip with 22nm lithography process and […] ⌘ Read more
The Nitrogen8M Plus SMARC from Laird Connectivity is a high-performance embedded computing module featuring a Quad-core Arm-A53 along with a 2.3 TOPS NPU for machine learning inference and onboard Image Signal Processor (ISP). The product page indicates that the Nitrogen8M Plus features the NXP i.MX 8M Plus with the following architecture: i.MX 8M Plus — […] ⌘ Read more
Last month, Kontron unveiled their 3.5” Single Board Computer powered by a variety of Intel processors. The 3.5”- SBC-EKL can accommodate processors from the Atom X6000E series, the Celeron J6000/N6000 series and the Pentium J6000/N6000 series. The 3.5”- SBC-EKL is capable of supporting the following Intel processors: Intel Atom (x6211E) – Dual Core, 1.5M Cache, […] ⌘ Read more
Orange Pi launched today a single board computer board with a small form-factor based on the Allwinner H618 64-bit processor clocked at 1.5GHz. The Orange Pi Zero 3 is equipped with one Gigabit Ethernet port with PoE support, various GPIOs and Wi-Fi/BT 5.0 connectivity. This Orange Pi board comes in a similar form-factor (50 x […] ⌘ Read more
The K3831-H Thin mITX is the latest Kontron’s motherboard powered by Intel Core i9/i7/i5/i3 and Intel Pentium/Celeron processor series. Some of the key features on this product are its DDR5 memory support, dual GbE ports and multiple display interfaces. As its name implies the SOM3588 is built on the RockChip RK3588 processor with an 8nm […] ⌘ Read more
The K3831-H Thin mITX is the latest Kontron’s motherboard powered by Intel Core i9/i7/i5/i3 and Intel Pentium/Celeron processor series. Some of the key features on this product are its DDR5 memory support, dual GbE ports and multiple display interfaces. Equipped with 2 SODIMM Sockets DDR5-5600, the K3831-H supports a maximum of 64GB of Dual Channel […] ⌘ Read more
Texas Instruments recently launched two development kits based on the CC2340R5 and the CC1314R10 wireless microcontrollers. These Launchpads support protocols such as Bluetooth 5 Low Energy, Sub-1 GHz, Wi-SUN, etc. The Launchpad based on the CC2340R5 microcontroller provides support for protocols such as Bluetooth 5.3 Low Energy, Zigbee, SimpleLink TI 15.4 stack (Sub 1GHz) and […] ⌘ Read more
The Indiedroid Nova is a single board computer with the same form factor as the popular Raspberry Pi 4B and powered by the Rockchip RK3588S SoC. This SBC supports up to 16GB of RAM and offers 8K video capability. The Indiedroid Nova is equipped with the Rockchip RK3588S System-on-Chip (SoC) similarly as the NanoPi R6C […] ⌘ Read more
The xG27-DK2602A development kit is a tiny board featuring a Silicon Labs Wireless Gecko SoC for portable IoT applications. This kit offers a range of features including four environment sensors, onboard debugger and up to 20 I/Os. The datasheet for this product indicates that the development kit features the EFR32BG27 Wireless Gecko System-on-Chip with integrated […] ⌘ Read more
Waveshare Electronics recently featured a computer module that combines versatile features with a compact form factor. The Core3566 integrates a Rockchip RK3566 processor running at 1.8GHz and a 0.8 Neural Processing Unit. This Waveshare computer module features the same Rockchip processor and provides similar features as the Radxa ROCK3 Model C SBC covered earlier this […] ⌘ Read more
Aries Embedded recently launched the MSMP1 that meets the Open Standard Module (OSM) guidelines. This embedded product is built upon the architecture of STMicroelectronics STM32MP1 family and offers a robust computing solution with single/dual Cortex-A7 cores along with a Cortex-M4 coprocessor. According to the product announcement, there are two module variants based on the following […] ⌘ Read more
ICP presented today the NANO-ADL-P single board computer which is designed to deliver high-performance in a compact form factor. The device comes with up to 16GB RAM, dual 2.5 GbE LAN ports, and multiple display interfaces. The NANO-ADL-P datasheet indicates that this device can be equipped with any of the following 12th Gen. Intel mobile Alder […] ⌘ Read more
The Arduino UNO R4 Wi-Fi is the newest addition to the UNO board lineup, combining a 32-bit Renesas microcontroller with the ESP32-S3 Wi-Fi module. This board introduces advanced features, expanded memory and it’s compatible with most shields and accessories designed for the UNO form-factor. The UNO R4 WiFi features the RA4M1 series microcontroller from Renesas. […] ⌘ Read more
Today, M5Stack launched a limited edition of the M5Stack Core host which is based on the Espressif ESP32 chipset. The CORE Metal is equipped with a 2” IPS display, buttons, multiple I/Os and it’s compatible with Arduino, MicroPython and other user-friendly programming platforms. This limited edition device features the same ESP32 microcontroller as the […] ⌘ Read more
The iMX93 uCOM is an ultra compact board featuring two ARM Cortex A55 processors along the Ethos-U65 neural processing unit for cost-effective ML applications. The device is an advanced application processor module designed to cater to the needs of various industries, including industrial automation, smart city, communication gateways, robotics, etc. This new product developed […] ⌘ Read more
The Portenta C33 is a compact module based on an ARM Cortex M33 microcontroller from Renesas Electronics. Featuring integrated Wi-Fi and Bluetooth Low Energy connectivity, as well as several I/Os, the Portenta C33 offers a viable solution for a wide range of applications, including IoT gateways and remote control systems. At the heart of […] ⌘ Read more
AAEON’s RTC-1020 is a rugged tablet computer designed to withstand challenging environments while delivering powerful performance. The RTC-1020 is equipped with a 2270mAh battery, a 10.1” FHD screen, 1x GbE LAN and support for Wi-Fi/BL 5.1 and LTE connectivity. According to the product page mentions that the RTC-1020 is compatible with the following Intel processors: […] ⌘ Read more
Today, IBASE revealed an embedded platform powered by the NVIDIA Jetson AGX ORIN modules, designed for AI applications in smart retail, healthcare, manufacturing, and other industries. The EC3500 is also equipped with 1x 10 GbE LAN, 1x HDMI 2.1 port and many other expansion ports. The product announcement indicates that the IBASE EC3500 features an […] ⌘ Read more
Boardcon introduced last week a System-on-Module featuring the octa-core Rockchip RK3588S System-on-Chip. Additionally, the company has released a companion board with support for GbE LAN, Wi-Fi/BL 5.1, dual displays and camera interfaces. Unlike the PICO3566 SoM (RK3566) recently covered, this new Boardcon embedded product boasts the Rockchip RK3588S SoC. The SBC also features 8GB […] ⌘ Read more
URANUS is an AI edge fanless embedded system designed to be compatible with multiple NVIDIA Jetson modules. This compact platform is designed to handle various neural networks and offers support for LTE and Wi-Fi connectivity. The SmartCow URANUS is compatible with the NVIDIA Jetson Nano, TX2 NX, and Xavier NX modules to meet different application […] ⌘ Read more
The PICO3566 is a System-on-Module based on the quad-core Rockchip RK3566 processor clocked at 1.8GHz. Boardcon Embedded Design states that this SoM can be used as a drop-in replacement to the versatile Raspberry Pi CM3+. Unlike the RPi CM3+ (BCM2837B0, 4x Cortex-A53 1.2GHz), the PICO3566 SoM accommodates the Rockchip RK3566 System-on-Chip. RK3566 – 64-bit Quad-core […] ⌘ Read more
The CM4 Sensing is an industrial computer designed to address the specific requirements of IoT and data acquisition applications. Leveraging the Raspberry Pi Compute Module 4 (CM4), this compact device offers a versatile and reliable solution for industrial environments. As its name implies, this new EDATEC industrial computer is based on the Raspberry Pi Computer […] ⌘ Read more
The ESP32CAM-PSRAM is a portable development board featuring an ESP32 microcontroller and a 2 Megapixel camera. The new embedded device from M5Stack is capable of supporting image transmission via Wi-Fi and it can be debugged using a USB Type-C port. The product images show that this development board integrates an ESP32-WROVER microcontroller with a PCB […] ⌘ Read more
The Station P2S, a compact and versatile mini PC that runs on the 64-bit RK3568 SoC. Moreover, the new mini PC offers flexible storage options and it supports dual GbE LAN, dual-band Wi-Fi, and 4G LTE network compatibility. The new Station P2S comes in a similar form-factor and it’s powered by the same processor as […] ⌘ Read more
This month, Wallystech introduced a router board powered by the Qualcomm IPQ9574 to deliver Wi-Fi 7 connectivity. The DR9574 includes up to 6x LAN ports (2x 10GbE + 4x 1GbE) and multiple M.2 slots for expansion. This new Wallystech router board is based on the Qualcomm-Atheros IPQ9574 chipset which appears to be part of the […] ⌘ Read more
Today, DFRobot launched a small single-board computer that combines the Rockchip RK3308 quad-core processor with a RISC-V 32-bit coprocessor. The open source Unihiker is equipped with multiple built-in sensors and it can be programmed with Python and other Open source programming languages. According to the Wiki pages, the Unihiker features the following two processors: […] ⌘ Read more
A few weeks ago, Advantech released a compact single board computer built on the MediaTek Genio 1200 Octa-core processor with a 4.8 TOPs AI processing unit (APU). The SBC also supports Wi-Fi 6 and 5G connectivity for demanding IoT applications. The RSB-3810 Pico-ITX is powered by the high-performing MediaTek Genio 1200 processor with TSMC N6 […] ⌘ Read more
iWave Systems launched last month a 45mm x 45mm System-on-Module integrating the latest NXP i.MX 91 System-on-Chip with EdgeLock Secure Enclave. Moreover, interfaces such as dual GbE, dual USB ports and diverse I/Os required in smart factory, smart home, medical devices and smart metering applications The iWave i.MX 91 OSM is one of the latest […] ⌘ Read more
ICOP Technology recently launched an ultra-compact platform built around the NXP iMX8 mini CPU equipped with up to 2GB LPDDR4 DRAM and wide input voltage range support. The VOX-070-TS-N8M is based on the NX8MM-D168 System-on-Module equipped with the NXP I.MX8M Mini Quad-Core Cortex-A53 Arm CPU with 3D GPU and includes advanced 14LPC FinFET process technology. […] ⌘ Read more
The WuKong Board H3 Zero is a small single board computer powered by a quad-core Allwinner H3 processor. The board comes with 10/100Mbps Ethernet support and various GPIOs for interfacing external devices. This board appears to be a Orange Pi Zero LTS clone since it features the same processor and provides very similar peripherals. The […] ⌘ Read more
Crowdsupply launched last month a tiny embedded board powered by an ATmega32 microcontroller. This open-source device features an USB Type-C port and it provides up to 23x IOs with support for serial protocols as I2C, SPI, etc. The product page indicates that the Epi 32U4 features the same microcontroller as the Arduino Leonardo, in this […] ⌘ Read more
The company GEEKOM launched today two mini-PCs built around the Ryzen 9 and Ryzen 7 AMD processors. The AS 6 supports DDR5 memory, 8K video output, up to 2TB of storage and multiple I/O ports. The product page states that these new products were co-developed with ASUS. In this case, the GEEKOM AS 5 is […] ⌘ Read more
Armbian launched in May their latest Linux distribution “Armbian 23.05 Suni” with various updates for the Debian community. Similarly, DietPi v8.18 has provided enhancements for the Quartz64 SBC and PiHole support for the RISC-V architecture. Armbian: Armbian is an open-source OS based on Linux designed specifically for ARM-based single-board computers (SBCs). It provides a lightweight […] ⌘ Read more
Last month, Axiomtek launched a palm-sized AI developer kit compatible with the NVIDIA platform to deliver up to 21 TOPs of AI computing performance and reduce product development time. As mentioned above, the AIE110-XNX is built around the powerful NVIDIA Jetson Xavier NX SoM with the following features: NVIDIA Jetson Xavier NX: CPU – 6-core […] ⌘ Read more
Kickstarter recently featured a compact USB infrared transceiver based on the Raspberry Pi RP2040 microcontroller. The PiBeam can be used to remotely control electronics such as laptops, TVs, etc. or it can be used as a Python-based learning platform. The PiBeam from SB Components seems to be very similar to their HackyPi launched earlier this […] ⌘ Read more
The Milk-V Duo is a small RISC-V embedded platform capable of running Linux and RTOS. The low-cost device features up to 26x GPIOs, optional 10/100Mbps Ethernet support and integrated with a H.264/H.265 video compression encoder and ISP. The product page indicates that his Milk-V Duo is based on the SOPHGO CVITEK CV1800B (C906 @1Ghz + […] ⌘ Read more
This week, Variscite revealed at Computer that they will soon release a low-cost System-on-Module based on the latest NXP i.MX 91 processor optimized for Linux-based applications. According to the press release, the new VAR-SOM-MX91 will be featured in a similar form-factor as other Variscite products from the VAR-SOM Pin2Pin family (i.e. VAR-SOM-MX93). This will allow […] ⌘ Read more
The global distributor Digilent recently announced that the new Analog Discovery 3 test instrument will arrive in June and it will still be supported by the free software Waveforms which is compatible with Windows, Mac and Linux. The product page describes the following: “the AD3 boasts a larger-than-ever buffer size, allowing more data to be sent […] ⌘ Read more
Compulab introduced today a low-cost embedded device built around a dual-core ARM Cortex-A55 and the Arm Ethos U-65 microNPU. The company has also launched a compatible carrier board with mainline Linux support and RTOS. The Compulab UCM-iMX93 is built around the same NXP processor as the VAR-SOM-MX93 (Variscite) launched earlier this year. There are three […] ⌘ Read more
The DPS310/368 Kit2Go from Infineon is a low-cost development board powered by the XMC100 industrial microcontroller. The compact embedded board can be quickly integrated into IoT and embedded applications since it supports the Arduino IDE platform. Both development boards implement the XMC1100 (32-bit Arm Cortex-M0) microcontroller which belongs to the XMC1000 family of industrial MCUs […] ⌘ Read more
The Milk-V Mars is a new single board computer built on the StarFive JH7110 RISC-V processor. The device is featured in a Raspberry Pi SBC form-factor and it supports up to 4K resolution. According to the announcement page, the Milk-V Mars is based on the StarFive JH7110 quad-core processor also seen in the Star64 single […] ⌘ Read more
The Debix Model B is a single board computer integrating the NXP i.MX8M Plus processor with 2.3 TOPs NPU and with extended operating temperature range. The new embedded device comes in a Raspberry Pi form-factor and offers similar peripherals. The company states that the only difference between the Debix Model A launched last year and […] ⌘ Read more
Estone Technology just launched an embedded board based on the NXP i.MX8M Plus processor along with a 2.3 TOPS Neural Processing Unit. Some of the features found include a RJ45 port and an onboard voice DSP. The EMB-2239 is another single board computer integrating this quad-core NXP processor similarly to the eDM-SBC-iMX8MP from DATA MODUL […] ⌘ Read more
CrowdSupply featured today the new AntSDR E200 software-defined radio (SDR) educational platform optimized for applications involving Wi-Fi, GSM, LTE and other wireless solutions. The product page shows that there are two AntSDR E200 variants available. However, both variants integrate a Xilinx FPGA from the Zynq-7000 family. XC7Z020-CLG400 — 85k Logic Cells, 53K LUTs, 220 DSP […] ⌘ Read more
This month, EDATEC launched an industrial embedded computer built around the Raspberry Pi Compute Module 4. The CM4 Industrial comes with two RJ45 ports, a 4G/LTE module, certified 2.4/5.8G dual-band Wi-Fi, Bluetooth and support for external antennas. This is another computer system designed for industrial applications based on the Raspberry Pi Computer Module 4. The […] ⌘ Read more
Sipeed launched yesterday the Tang Nano 20K development board powered by a GowinSemi FPGA from the GW2A series. This compact embedded platform offers the same amount of logic units as the Tang Primer 20K launched last year. The latest datasheet indicates that the Tang Nano 20K features the GW2AR-18 and an onboard Buffalo Labs BL616 […] ⌘ Read more
The EmETX-i92U0 is an industrial Computer-on-Module designed with the 11th Generation Intel Core processors. This customizable board delivers Ultra HD display, codec support, up to 12x USB ports and wide expansion ports. The EmETX-i92U0 is featured in a COM express form-factor and it’s built on Intel’s 10nm SuperFin process technology. The product page shows that […] ⌘ Read more
Orange Pi recently launched a single board computer equipped with an octa-core Rockchip RK35588 SoC along with an up to 6 TOPs NPU. The new SBC can handle up to four displays, two 2.5GbE LAN interfaces and many other expansion ports. Unlike the Orange Pi 5 (Rockchip RK3588S), this new SBC implements the 64-bit RK35588 […] ⌘ Read more
SolidRun’s new industrial System-on-Module features the AM64x Sitara family of processors from Texas Instruments. The embedded products provide support for multi-protocol industrial ethernet with TSN and they are compatible with new the HummingBoard-T carrier boards also from SolidRun. The product page shows that there are two Sitara SOM variants available for now: the Sitara AM6442R […] ⌘ Read more
The eDM-SBC-iMX8MP is a Single Board Computer that runs Linux on the NXP i.MX8M Plus quad-processor with an integrated Neural Processing Unit and HiFi4 DSP. The datasheet indicates that this DATA MODUL SBC can be ordered with two variants of the NXP i.MX8M Plus processor. The main differences noticed is that one of the processor […] ⌘ Read more
The Jetsys-5330 is a rugged small computer system built around the NVIDIA Jetson Orin AGX Orin System-on-Module. The new device from Elma Electronic features multiple expansion ports and can handle up to 6x GMSL2/GMSL1 cameras. The JetSys-5330 AI performance varies depending on the Jetson AGX Orin module selected. For example, the Jetson AGX Orin 32GB […] ⌘ Read more
The Coral Dev Board Micro is a small dual-core microcontroller device with a 4 TOPS ML accelerator and built-in camera. These embedded boards, the compatible PoE module and Wi-Fi/BT5.0 module are already available from a couple of global distributors. The product page specifies that the Dev Board Micro features a high-performing, low-power microcontroller that belongs […] ⌘ Read more~
ICP Germany just launched a high-performance Single Board Computer based on Intel Celeron processors. The HYPER-EHL board offers numerous serial ports and it can support up to two simultaneous displays via HDMI and iDPM. The datasheet describes that the HYPER-EHL comes with 4GB LPDDR4x memory by default, but it can be configured with up to […] ⌘ Read more
iWave Systems recently announced the iW-RainboW-G54S STM32MP13x LGA System on Module aimed at low-power embedded and consumer applications. The company also unveiled a compatible SBC to provide access to extensive peripherals. This iWave Systems OSM can be configured with any of the following three STM32 microcontrollers with Armv7 Architecture: STM32MP131 – 32-bit Single Arm Cortex-A7 […] ⌘ Read more
MYIR launched this month an industrial development platform based on the Xilinx XC7Z010/20 System-on-Chip. The base board supports up to 3x Gigabit ports, CAN interfaces and other flexible peripherals. The MYD-Y7Z010/20-V2 CPU module has a 10-layer PCB design and it can accommodate the Zynq-7010 or the Zynq-7020 SoC with the following specs: Zynq-7010/7020 SoC – […] ⌘ Read more
The Hadron Carrier is an ultra small, rugged carrier board compatible with multiple NVIDIA Jetson modules. This new product from Connect Tech comes with one GbE connector, camera support and various expansion headers. The top side of the board features a SODIMM 260-pin connector to accommodate NVIDIA modules such as the Jetson Orin NX, Orin […] ⌘ Read more
The LPC860-MAX by NXP is an evaluation board targeting applications such as motor control, wearables and other consumer products. The eval board is equipped with a 32-bit ultra-low power Arm Cortex-M0+ and up to 54x GPIOs. This specific evaluation board integrates the LPC86x family of microcontrollers. Refer to the table below to see other MCUs […] ⌘ Read more
ADLINK presented today a fanless embedded media player built around the 11th Gen Intel Core processors. The EMP-510 can handle up to four simultaneous displays, two 2.5 Gigabit ethernet interfaces and other serial ports. The product announcement reveals that the EMP-510 Series can be ordered with the following Intel processors with 10nm process. i5-1145G7E — […] ⌘ Read more
DFRobot launched today an ESP32-based development board that can be used in computer vision and signal processing applications. The compact module also includes Li-on battery charging features. DFRobot is offering the FireBeetle 2 with the ESP32-S3-WROOM-1-N16R8 or ESP32-S3-WROOM-1U-N16R8 module. The latter ESP32 module comes with an antenna connector. ESP32-S3 (N16R8) — Dual-core Xtensa LX7 (up […] ⌘ Read more
ICOP launched last month a single board computer based on the i.MX8M mini multicore processor designed for machine vision, industrial systems, embedded systems and smart retail applications. The datasheet indicates that the NX8MM-35 integrates the following NXP multicore processor along with a GCNanoUltra for 3D acceleration/GC320 for 2D acceleration and support for OpenGL ES 2.0. […] ⌘ Read more
Last week, Avalue launched an Intel Atom motherboard optimized for industrial and commercial applications such as gaming, retail, digital signage, etc. The EMX-EHLP supports up to 4x 2.5GbE LAN ports, triple display, and flexible expansion slots. The product announcement states that the EMX-EHLP can accommodate Atom x6000E and Pentium/Celeron N/J series CPUs. The system memory can […] ⌘ Read more
This month’s HackerBox provides a learning kit based on Arduino Nano boards and various breakout modules used for implementing user-friendly FM radio projects. The new HackerBox includes two standard Arduino Nano boards based on the 8-bit Atmel microcontroller (up to 16MHz) with 2KB SRAM and 1KB EEPROM. ⌘ Read more
The ARV6X by Ark Electronics is a tiny flight controller that follows the latest Pixhawk v6 set of standards. The open source device features a high-performance STM32 microcontroller along with triple synced IMUs. The ARV6X comes in a System-on-Module form-factor and integrates the STM32H753 microcontroller which is a mandatory specification for the Pixhawk 6V standards. […] ⌘ Read more
Kickstarter featured this week an Open-source development ESP32-based board designed for learning and quick prototyping. The TESPuino provides up to 14x GPIOs, 1x MicroSD card slot for storage and 1x USB Type-C port programming and power. It seems that there will be two TESPuino versions, however the product page mentions that the ESP32–U4WDH variant has […] ⌘ Read more
The WVR audio development is a small embedded device featuring a ESP32 module and a 32-bit stereo DAC from Texas Instruments. This open-source device supports MIDI and it can be configured from a Web GUI for convenience. This is another audio development board featuring a ESP32 microcontroller. The Loud ESP launched in March 2023 on […] ⌘ Read more
IBASE recently launched a Mini-ITX compatible with AMD Ryzen processors from the Embedded R2000 family. The MI993 includes 2x GbE LAN ports, 1x SATA port, up to 4x display ports and various serial interfaces. The product announcement mentions that the MI993 can be equipped with the following AMD processors with 14nm process. R2544 — 4C/8T, […] ⌘ Read more
The LattePanda Sigma is a new single board computer featuring a 13th gen i5 processor along with an ATmega32 coprocessor. The device is equipped with multiple interfaces and flexible expansion ports. The new LattePanda model is available only with the following Intel core processor with support for four 4K simultaneous displays: i5-1340P – 12C/16T (4P+ […] ⌘ Read more
Earlier this month, Renesas announced that their new CK-RA6M5 and CK-RX65N embedded kits are now supported by the Azure Cloud platform. These devices are loaded with various onboard sensors and they are also compatible with the Edge Impulse machine learning firmware. Both Renesas Cloud kits provide very similar peripherals, however the first board is […] ⌘ Read more
The Turing RK1 is a computer module powered by the Octa-core Rockchip RK3588 System-on-Chip. The RK1 will be available with up to 32GB RAM, 16GB eMMC storage and various other interfaces. The Turing RK1 is compatible with the Turing Pi 2 mini-ITX cluster board released last year. RK3588S SoC — Quad-core Cortex-A76 (up to 2.4GHz), […] ⌘ Read more
Gowin Semiconductors announced this week an evaluation board based on the GW5AT-138 FPGA series targeting communications, server imaging, automotive and other high-speed applications. The GW5AT FPGA (22nm process) belongs to the fifth generation product from the Gowin Arora family. Refer to the GOWINSEMI Arora V FPGA page for more information. GW5AT-LV138FPG676A — 138K LUT4, 298 […] ⌘ Read more
The Kolibri is a USB dongle that integrates the Lattice iCE40 FPGA, a RP2040 microcontroller and a PMOD connector for I/O expansion. The compact device is also compatible with the Open Source Project IceStorm. The Kolibri features another Lattice low-power FPGA from the iCE40 family as most Machdyne devices. ICE40HX4K – 7680 LUTs, 2 PLLs; […] ⌘ Read more
BIGTREETECH revealed a Single Board Computer integrating the Allwinner H616 System-on-Chip. The embedded device mirrors the Raspberry Pi SBC form-factor and it provides similar peripherals. This SBC features the same processor seen in other recently introduced BIGTREETECH embedded products, for example the Pad 7 and the BIGTREETECH CB1. Allwinner H616 – Quad-core Cortex-Arm A53 (up […] ⌘ Read more
MicroSys unveiled this month a Single Board Computer featuring the NXP S32G multicore processor optimized for automotive networking applications. The miriac SBC-S32G399A features up to 18x CAN interfaces, 12x Analog input and various ethernet ports. This carrier board integrates the miriac MPX-S32G399A System on Module introduced last year: NXP S32G399A– 8x Arm Cortex-A53, 4x Cortex-M7 […] ⌘ Read more
Bitcraze recently featured the Flapper Nimble+ which is described as the “world’s first commercially available tailless flapping wing robot designed for academic research or entertainment.” The Flapper Nimble+ is built around the Crazyflie Bolt 1.1 flight controller that uses an STM32 chip as the main application MCU and a nRF51 chip used for radio and […] ⌘ Read more
The BIGTREETECH Pad 7 is an Open Source handheld device designed for 3D printing applications and compatible with Klipper firmware. The Pad 7 features an RJ45 ethernet port, CAN port and many other interfaces. The product page indicates that the new Pad 7 includes the BIGTREETECH CB1 module with Klipper and KlipperScreen pre-installed, but it […] ⌘ Read more
The ESP Terminal from Elecrow is a handheld device based on the ESP32-S3-WROOM Wi-Fi + Bluetooth LE microcontroller. The compact device includes multiple terminal connectors for sensors and LiPo battery support. The ESP32 Terminal is slightly larger than the BPI-Centi-S3 based on a similar ESP32 module. ESP32-S3-WROOM-N16RB – Xtensa 32-bit LX7 dual core (up to […] ⌘ Read more
EDATEC revealed yesterday a small embedded device with support for the Raspberry Pi CM4. The ED-IPC2010 comes in an aluminum alloy case and it includes an onboard encryption chip. The EDATEC is another industrial-grade device based on the Raspberry Pi CM4 similar to the IGN800 from Onlogic seen last year. Broadcom BCM2711 — Quad-core […] ⌘ Read more
The UP Squared Pro 7000 series from AAEON is an embedded platform built around the Intel Core/Atom/N-Series processors. These devices come with up 32GB LPDDR5 Memory, 64GB eMMC, dual 2.5 GbE and multiple expansion interfaces. The UP Squared Pro 7000 supports the following Intel Alder Lake-N processors: Core i3-N305 — 8C/8T, (1.8 – 3.8 GHz); […] ⌘ Read more
The SoftRF T-BeamSUPREME is a new small embedded device designed and produced by LILYGO and SoftRF. The new development board is compatible with U-blox MAX-M10S modules and Seemtech SX1262 LoRa modules. The SoftRF T-BeamSUPREME comes with a ESP32-S3 microcontroller as other recently launched LILYGO devices (T-TWR, T-SIM7080G) ESP32-S3 – Xtensa 32-bit LX7 dual core (up ... ⌘ Read more
The SI-111 is a palm-size fanless 4K digital signage player featuring Atom/Celeron low power processors. The new IBASE device includes a 2.5 GbE LAN port, 1x HDMI 2.0 port and multiple serial interfaces. This IBASE product features a FCBGA1493 CPU socket and it will come with the following two Intel Elkhart Lake processors: x6211E — […] ⌘ Read more
This month, BananaPi unveiled a compact development board equipped with a 1.9” LCD display. The BPI-Centi-S3 is built around the ESP32-S3 microcontroller enabled with 2.4 GHz Wi-Fi and Bluetooth 5 connectivity. The BPI-Centi-S3 integrates the Espressif ESP32-S3 microcontroller as other new BananaPi products released recently (i.e., BPI-PicoW-S3, BPI-Leaf-S3): ESP32-S3 – Xtensa 32-bit LX7 dual core […] ⌘ Read more
ThePiHut featured this week an open source ePaper watch powered by an ESP32 module. Some of the peripherals featured include a 3-axis accelerometer, a vibration motor, a LiPo battery connector and many other features. The Watchy has Bluetooth and Wi-Fi connectivity since it features the following microcontroller: ESP32-PICO-D4 — Xtensa 32-bit LX6 MCU (up to […] ⌘ Read more
Today, TUXEDO Computers launched a Linux gaming laptop equipped with the Core i9-13900HX processor, a 2.5 GbE LAN port, a 99Wh battery and an optional Cherry MX mechanical keyboard. Additionally, the Stellaris 16 Gen 5 features a 240Hz display and a Thunderbolt 4 port. The Stellaris 16 is only available with the following 13th Gen […] ⌘ Read more
The Adafruit Feather RP2040 RFM69 Packet Radio is a compact board providing up to 21x GPIOs, 1x STEMMA connector, LiPo connector and it’s compatible with Arduino/CircuitPython. According to the product page, this new Feather module is based on the Adafruit Feather RP2040 board launched last year. RP2040 — 32-bit Dual Arm Cortex M0+ processor (up […] ⌘ Read more